| 7 0673 Rollix Slewing Ring Bearings | Snap Ring Outside Diameter:139.7 mm; da (min):91 mm; a (max):2.9 mm; r1:0.5 mm; d:85 mm; b (min):3.1 mm; Weight:0.863 kg; D:130 mm; Dynamic Load Rating:49,500 N; Fillet Radius/Chamfer:1.1 mm; Limiting Speed - Grease:5,000 rpm; Snap Ring Width:2.8 mm; Configuration:Single Row; Dx (min):141.5 mm; ra (max):1 mm; Cy (max):5.3 mm; Factor fo:15.7; Da (max):124 mm; B:22 mm; Enclosure:Single Shield with S; |
| 7 1385 03 Rollix Slewing Ring Bearings | G1 - Heat Generation Factor (Roller-Raceway):18.4; Y - ISO Factor9:1.44; Da - Cup Frontface Backing Diameter:60.96 mm; Cg - Geometry Factor:0.0692; r - Cup Backface To Clear Radius2:0.51 mm; a - Effective Center Location3:-2.3 mm; d:38.000 mm; da - Cone Frontface Backing Diameter:42.42 mm; Cage Type:Stamped Steel; C0 - Static Radial Rating:55000 N; Ab - Cage-Cone Frontface Clearance:1.8 mm; Aa - Cage-Cone Backface Clearance:0 mm; |
| 12.50.3520.001.49.1502 Standard 5 Slewing Ring Bearings | Weight:87 lb; C0 - Static Load:147000 lb; Oil Lubrication - M/N Seal:900 rpm; Eng Internal Radial Clearance - Max:0.0067; Dimension RV:0.39 in; e - Geometry Factor:0.25; Pre Install Clearance Max:0.0067 in; Dimension L:4.94 in; Oil Lubrication - T Seal:1700 rpm; Grease Lubrication - M/N Seal:900 rpm; Full Timken Part Number:QVPG22V100SB; Shaft Size :100 mm; Dimension D Max:14.50 in; Dimension B:9.38 in; |
| 31 0641 01 Rollix Slewing Ring Bearings | Design Units:METRIC; G1 - Heat Generation Factor (Roller-Raceway):20.3; Series:16000; B:21.400 mm; a - Effective Center Location3:-4.1 mm; e - ISO Factor8:0.4; Cg - Geometry Factor:0.0707; C90 - Dynamic Radial Rating (90 million revolutions)4:14700 N; Db - Cup Backface Backing Diameter:62.99 mm; db - Cone Backface Backing Diameter:51.05 mm; Ab - Cage-Cone Frontface Clearance:1.8 mm; G2 - Heat Generation Factor (Rib-Roller End):10.6; |
| 25 0411 01 Rollix Slewing Ring Bearings | B - Cone Width:0.7710 in; C90 - Dynamic Radial Rating (90 million revolutions)4:3180 lbf; Aa - Cage-Cone Backface Clearance:0.02 in; K - Factor7:1.53; Cup Part Number:14276-B; da - Cone Frontface Backing Diameter:1.46 in; a - Effective Center Location3:-0.17 in; Ca90 - Dynamic Thrust Rating (90 million revolutions)6:2080 lbf; Bearing Weight:0.6 lb; T - Bearing Width to Flange:0.3123 in; D1 - Flange Outer Diameter:2.8690 in; |
| 11.50.3347.001.49.1502 Standard 5 Slewing Ring Bearings | Fillet Radius/Chamfer:0.3 mm; Configuration:Single Row; Weight:0.018 kg; Dynamic Load Rating:4,600 N; Radial Clearance:0.011 to 0.025 mm; Static Load Rating:2,550 N; D:30 mm; Limiting Speed - Grease:24,000 rpm; d:17 mm; Bore Type:Cylindrical Bore; da (min):19 mm; B:7 mm; Enclosure:Double Shield; Factor fo:14.7; Da (max):28 mm; ra (max):0.3 mm; |
| 11.50.3747.001.49.1502 Standard 5 Slewing Ring Bearings | Design Units:Imperial; Da - Cup Frontface Backing Diameter:3.46 in; Cg - Geometry Factor:0.0912; Cup Part Number:28521; Db - Cup Backface Backing Diameter:3.27 in; r - Cup Backface To Clear Radius1:0.030 in; Series:28500; C - Cup Width:0.7813 in; e - ISO Factor2:0.38; D:3.6250 in; Y - ISO Factor3:1.59; |
| 22 0541 01 Rollix Slewing Ring Bearings | Housing Width:6.3 in; Dimension H2:14.6 in; Support Type:Four-Bolt Plummer Bl; Dimension L:20.0 in; Bearing Number:MSM110BX; Pillow/Plummer Block Style:Split Cylindrical Ho; Series Type:Medium Series; Dimension H1:1.5 in; Bearing Type:Split Cylindrical Ex; Cr - Dynamic Load Rating:102063 lbf; Note:This product line wa; Dimension H:6.378 in; Dimension M:7.0 in; Maximum Speed:1820 rpm; Cor - Static Load Rating:133087 lbf; |
| 68733A Franke Slewing Ring Bearings | B - Cone Width:17.463 mm; Y - ISO Factor9:1.48; Db - Cup Backface Backing Diameter:77.98 mm; Bearing Weight:0.5 Kg; Da - Cup Frontface Backing Diameter:83.06 mm; Cone Part Number:18780; K - Factor7:1.44; Cage Type:Stamped Steel; C1 - Dynamic Radial Rating (1 million revolutions)5:12300 lbf; G1 - Heat Generation Factor (Roller-Raceway):28.6; Series:18700; r - Cup Backface To Clear Radius2:1.27 mm; Design Units:Imperial; |
| 68727A Franke Slewing Ring Bearings | dc (min):102 mm; B:42 mm; Limiting Speed - Grease:3,600 rpm; Bore Type:Cylindrical Bore; db (min):84 mm; Dynamic Load Rating:228,000 N; db (max):99 mm; Db (max):153 mm; Configuration:Single Row; Fillet Radius/Chamfer:3 mm; ra (max):2.5 mm; Outside Ring Inside Diameter:152 mm; Radial Clearance:0.040 to 0.075 mm; Weight:5.260 kg; Db (min):166 mm; Da (max):166 mm; d:70 mm; Enclosure:Open; r1:3 mm; ra1 (max):2.5 mm; |
| No. | Brand | D | k | s | i | T | E | A | H |
| 121.32.3750.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 38 0541 01 | Rollix | 140 mm | - | - | - | - | - | - | - |
| 36 0841 01 | Rollix | 72 mm | - | - | - | - | - | - | - |
| 8 0675 | Rollix | - | - | - | - | - | - | - | - |
| 29 0541 01 | Rollix | - | - | - | - | - | - | - | - |
| 1 0289 06 | Rollix | 280 mm | - | - | - | - | - | - | - |
| 32 0841 01 | Rollix | - | - | - | - | - | - | - | - |
| 192.50.4000.990.41.1502 | Standard 5 | 4.8750 in | - | - | - | - | - | - | - |
| 2 0422 | Rollix | - | - | - | - | - | - | - | - |
| 34 0541 01 | Rollix | - | - | - | - | - | - | - | - |
| 121.45.5600.990.41.1502 | Standard 5 | 340 mm | - | - | - | - | - | - | - |
| 39 0741 01 | Rollix | - | - | - | - | - | - | - | - |
| 2 1225 | Rollix | 360 mm | - | - | - | - | - | - | - |
| 12.50.3520.001.49.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 6 0574 09 | Rollix | - | - | - | - | - | - | - | - |
| 22 0641 01 | Rollix | - | - | - | - | - | - | - | - |
| 37 0411 01 | Rollix | 374.650 mm | - | - | - | - | - | - | - |
| 23 0941 01 | Rollix | - | - | - | - | - | - | - | - |
| 26 0741 01 | Rollix | - | - | - | - | - | - | - | - |
| 11.50.3747.001.49.1502 | Standard 5 | 3.6250 in | - | - | - | - | - | - | - |
| 6 0307 | Rollix | - | - | - | - | - | - | - | - |
| 68637A | Franke | 75 mm | - | - | - | - | - | - | - |
| 3 0402 | Rollix | 720.000 mm | - | - | - | - | - | - | - |
| 1 088 | Rollix | - | 174.0 mm | - | - | - | 20 mm | - | - |
| 191.50.5600.990.41.1502 | Standard 5 | 30 mm | - | - | - | - | - | - | - |
| 12.50.3839.001.49.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 2 1295 | Rollix | - | - | - | - | - | - | - | - |
| 1 0626 | Rollix | - | - | - | - | - | - | - | - |
7 0885 01 Rollix Slewing Ring Bearings Video
Marpac Ignition Switch - Brass Style 7-0885 - Marine Engine ...
All brass construction with chrome plated face nut. 3 positions: Off-Ignition- Start. Automatic return to ignition from start position.Mounting stem 1-7/32 ...
1650-01-152-0885 - LINEAR ACTUATING CYLINDER ASSEMBLY ...
Product Details | LINEAR ACTUATING CYLINDER ASSEMBLY. 1650-01-152-0885 A cylinder containing a piston and other component parts designed to develop linear ...
Plating Marble Case for iPhone Xs XR X 7 8 Plus Back Cover ...
0885 2 · 98000 · 98999 2 · 98999 3 · 98999 4 · 98999 5 · Blue 0984 1 · Colorful 0835.Brand: Fiery TulipOther display features: WirelessColour: 0885 2
Briggs & Stratton 12E802-0885-01 - Briggs & Stratton Vertical ...
Cylinder, Head, Oil Fill diagram and repair parts lookup for Briggs & Stratton 12E802-0885-01 - Briggs & Stratton Vertical Engine.
CPC Scheme - G04F TIME-INTERVAL MEASURING - USPTO
TIME-INTERVAL MEASURING (measuring pulse characteristics G01R, e.g. G01R 29/02; in radar or like systems G01S; masers H01S ... G04F 1/00 ... G04F 7/0885.
Senate Bill 0885 (1999) - Michigan Legislature
Friendly Link: http://legislature.mi.gov/doc.aspx?1999-SB-0885 Public Act 389 of 2000 (Effective: 04/01/01) Find this PA in the MCL. Sponsor.